ciclo's Polo. R-line 1.2 TSI 90hp 119gr.

[patil]

Master Ciclo... I have a question regarding trunk light wiring.

Actually Indian Polo 6R does not come fitted with trunk light. I have retrofitted the trunk light and tapped the wiring from front dome light. So whenever any of the doors are opened trunk light will turn on, same way as footwell lights. I want to wire it like oem, so that light should lit only when trunk is opened and go off when trunk is closed. Is it possible?
I looked into wiring diagram, mentioned during your 2nd trunk light installation.
Pin 1 tapped from Pin1 T5h(Rear lid lock) RED/BLUE color wire.
Pin 2 from +30

Now the problem.. The RED/BLUE color wire in my car is in pin4, and a white wire is on pin1... please see picture.
How to proceed from here?

[benzinkopf]

I believe you can tap and use any usable 30+ power line for the trunk light but to make it work like oem, all you need is the right Ground wire, in this case either Ground wire of the rear lid locking motor or directly to T73a/35 bcm.


Sent from my iPhone using Tapatalk

[graaja]

This is the cluster from a T6 with custom firmware for Polo (vehicle picture, wheel circumference, tank level) and Kessy. No dealer will do this for you.

I will stop thinking about it even in my dreams then

[Adam87]

This is the cluster from a T6 with custom firmware for Polo (vehicle picture, wheel circumference, tank level) and Kessy. No dealer will do this for you.

I though T6 only came with 3D in colour not 2D, or is it because it's 2D FW on there?


Sent from my iPhone using Tapatalk

[favi]

Hiho ;>
Today I wanted to encode "Cornering Light With Reverse Gear". Unfortunately, but failure. Has anyone coded in Polo6R such a function?

[benzinkopf]

Yes. Byte 21 Bit 3. Its not "Cornering light" but "Foglight" instead.


Sent from my iPhone using Tapatalk

[ciclo]

Hiho ;>
Today I wanted to encode "Cornering Light With Reverse Gear". Unfortunately, but failure. Has anyone coded in Polo6R such a function?

viewtopic.php?f=56&t=58703&start=765#p491577

For front fog lights or bixenon, the cornering lights function can work on one or in the other. (depending on equipment)

[ciclo]

Master Ciclo... I have a question regarding trunk light wiring.

Actually Indian Polo 6R does not come fitted with trunk light. I have retrofitted the trunk light and tapped the wiring from front dome light. So whenever any of the doors are opened trunk light will turn on, same way as footwell lights. I want to wire it like oem, so that light should lit only when trunk is opened and go off when trunk is closed. Is it possible?
I looked into wiring diagram, mentioned during your 2nd trunk light installation.
Pin 1 tapped from Pin1 T5h(Rear lid lock) RED/BLUE color wire.
Pin 2 from +30

Now the problem.. The RED/BLUE color wire in my car is in pin4, and a white wire is on pin1... please see picture.
How to proceed from here?

... in your case (6R IND), the winner ('ground wire') for trunk light is purple/violet wire. You can check with a diagnostic lamp/multimeter before splice or damage this wire.

Power supply is right (from the dome light).

[favi]

Hiho ;>
Today I wanted to encode "Cornering Light With Reverse Gear". Unfortunately, but failure. Has anyone coded in Polo6R such a function?

viewtopic.php?f=56&t=58703&start=765#p491577

For front fog lights or bixenon, the cornering lights function can work on one or in the other. (depending on equipment)

Thank you very much

[ciclo]

I believe you can tap and use any usable 30+ power line for the trunk light but to make it work like oem, all you need is the right Ground wire, in this case either Ground wire of the rear lid locking motor or directly to T73a/35 bcm.


Sent from my iPhone using Tapatalk

No,... hmm ... and no.

Any power wire/line has its own fuse due to many reasons. Hmm, maybe, the electrical installation of the interior lights is one of the most manipulated by everyone.

T73a/35 = sunroof output

[ciclo]

Sent from my iPhone using Tapatalk

Hi there
read here
viewtopic.php?f=56&t=58703&p=520980#p520937

This is the cluster from a T6 with custom firmware for Polo (vehicle picture, wheel circumference, tank level) and Kessy. No dealer will do this for you.

I thought so.

[benzinkopf]

I believe you can tap and use any usable 30+ power line for the trunk light but to make it work like oem, all you need is the right Ground wire, in this case either Ground wire of the rear lid locking motor or directly to T73a/35 bcm.


Sent from my iPhone using Tapatalk

No,... hmm ... and no.

Any power wire/line has its own fuse due to many reasons. Hmm, maybe, the electrical installation of the interior lights is one of the most manipulated by everyone.

T73a/35 = sunroof output

Sure master. Connecting to any power line will not go through the exact fuse as intended. Btw, the T73a/35 is wrong? I may have overlooked the original my 6R diagram which is different from IND production or Bcm max? Thanks for the correction.


Sent from my iPhone using Tapatalk

[benzinkopf]

ok. Sorry. Totally my fault or typo. It should be T73a/31. [emoji23]


Sent from my iPhone using Tapatalk

[ciclo]

No worries, I am the first to make mistakes.
With the errors/tests, wisdom is attained (sometimes ).

[favi]

Little problem with The two static cornering lights turn on with reverse

Don't have BIT3