Help fitting Reverse Camera with RCD330 - Canbus
-
- New
- Posts: 42
- Joined: Sun Apr 26, 2020 10:08 am
- Drives: Polo 6C 1.4TDI 105HP
- Location: Netherlands
Re: Help fitting Reverse Camera with RCD330 - Canbus
@ iichel
I coded that I have Rear view camera, when i turn off byte 19 bit 4 then I will see the OPS.
This is the fault code.
1 Fault Found:
6720 - Rear View Camera
B1102 31 [009] - No Signal
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 3
Fault Frequency: 1
Reset counter: 100
Mileage: 64470 km
Date: 2021.01.03
Time: 12:11:45
Voltage terminal 30: 11.1 V
I coded that I have Rear view camera, when i turn off byte 19 bit 4 then I will see the OPS.
This is the fault code.
1 Fault Found:
6720 - Rear View Camera
B1102 31 [009] - No Signal
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 3
Fault Frequency: 1
Reset counter: 100
Mileage: 64470 km
Date: 2021.01.03
Time: 12:11:45
Voltage terminal 30: 11.1 V
- iichel
- Bling Bling Diamond Member
- Posts: 6361
- Joined: Fri Nov 14, 2014 2:14 pm
- Drives: Polo 6R 2.0 TDI, Passat B8 2.0 TSI
- Location: http://mypassat.nl/
Re: Help fitting Reverse Camera with RCD330 - Canbus
i guess you'll have to figure out why the radio isn't receiving a signal from the rvc
-
- New
- Posts: 42
- Joined: Sun Apr 26, 2020 10:08 am
- Drives: Polo 6C 1.4TDI 105HP
- Location: Netherlands
Re: Help fitting Reverse Camera with RCD330 - Canbus
Remove this
You will see a round rubber thing with wiring remove the rubber
Put a cable in the license plate light holder
You will see the cable is coming to the rubber whole, its little bit difficult but the cable is coming to the rubber whole
-
- Silver Member
- Posts: 493
- Joined: Wed Dec 07, 2016 8:34 pm
- Drives: Polo6r/1.2TSI/DSG7, T-roc'20 1.5TSI/DSG7
- Location: Foothills of Nilgiris, India
Re: Help fitting Reverse Camera with RCD330 - Canbus
Thanks for the picture
Please do as I suggest and tell me the results.
1. Please feed the camera power with +30
2. Ground connect wherever you want, but I suggest you to connect ground in front eg.. steering column ground point.
3. Connect can high and can low to your quadlock can wires as iichel suggested.
4. Coding is not required for such type of cameras.
5. In address 10, select automatic in ops display.
This should set everything right.
Good luck
Please do as I suggest and tell me the results.
1. Please feed the camera power with +30
2. Ground connect wherever you want, but I suggest you to connect ground in front eg.. steering column ground point.
3. Connect can high and can low to your quadlock can wires as iichel suggested.
4. Coding is not required for such type of cameras.
5. In address 10, select automatic in ops display.
This should set everything right.
Good luck
-
- New
- Posts: 42
- Joined: Sun Apr 26, 2020 10:08 am
- Drives: Polo 6C 1.4TDI 105HP
- Location: Netherlands
Re: Help fitting Reverse Camera with RCD330 - Canbus
But I have a 6C when i dont coded byte19 bit 4 i dont see anything only the opspatil wrote: ↑Mon Jan 04, 2021 5:09 pm Thanks for the picture
Please do as I suggest and tell me the results.
1. Please feed the camera power with +30
2. Ground connect wherever you want, but I suggest you to connect ground in front eg.. steering column ground point.
3. Connect can high and can low to your quadlock can wires as iichel suggested.
4. Coding is not required for such type of cameras.
5. In address 10, select automatic in ops display.
This should set everything right.
Good luck
Where in address 10 can I find the option automatic OPS?
I will do it tommorow, thank you
I will let you know the result.
Last edited by Mocro on Mon Jan 04, 2021 5:44 pm, edited 1 time in total.
- iichel
- Bling Bling Diamond Member
- Posts: 6361
- Joined: Fri Nov 14, 2014 2:14 pm
- Drives: Polo 6R 2.0 TDI, Passat B8 2.0 TSI
- Location: http://mypassat.nl/
Re: Help fitting Reverse Camera with RCD330 - Canbus
Video is not transmitted through the canbus. It needs the canbus for the dynamic lines. The video is transmitted to the blue block of the quadlock.
-
- Silver Member
- Posts: 493
- Joined: Wed Dec 07, 2016 8:34 pm
- Drives: Polo6r/1.2TSI/DSG7, T-roc'20 1.5TSI/DSG7
- Location: Foothills of Nilgiris, India
Re: Help fitting Reverse Camera with RCD330 - Canbus
Slight correction to my suggestion.Mocro wrote: ↑Mon Jan 04, 2021 5:25 pmI will do it tommorow, thank youpatil wrote: ↑Mon Jan 04, 2021 5:09 pm Thanks for the picture
Please do as I suggest and tell me the results.
1. Please feed the camera power with +30
2. Ground connect wherever you want, but I suggest you to connect ground in front eg.. steering column ground point.
3. Connect can high and can low to your quadlock can wires as iichel suggested.
4. Coding is not required for such type of cameras.
5. In address 10, select automatic in ops display.
This should set everything right.
Good luck
I will let you know the result.
I completely overlooked that you have rcd330 installed. After completing the wiring part, the camera must be coded.
Go to address 56, and enable byte3, bit6
Also remember, the power supply to camera must be +30 and not +15.
My sincere apologies for my suggestion number 4
- iichel
- Bling Bling Diamond Member
- Posts: 6361
- Joined: Fri Nov 14, 2014 2:14 pm
- Drives: Polo 6R 2.0 TDI, Passat B8 2.0 TSI
- Location: http://mypassat.nl/
Re: Help fitting Reverse Camera with RCD330 - Canbus
Patil, he has a Discover Media MQB in his Polo 6C, not an RCD330.
-
- New
- Posts: 42
- Joined: Sun Apr 26, 2020 10:08 am
- Drives: Polo 6C 1.4TDI 105HP
- Location: Netherlands
Re: Help fitting Reverse Camera with RCD330 - Canbus
I put the ACC to fuse 19
-
- Silver Member
- Posts: 493
- Joined: Wed Dec 07, 2016 8:34 pm
- Drives: Polo6r/1.2TSI/DSG7, T-roc'20 1.5TSI/DSG7
- Location: Foothills of Nilgiris, India
Re: Help fitting Reverse Camera with RCD330 - Canbus
Oh I got confused iichel. Thanks for pointing it out
So here is the coding for both Damon & Mocro
For RCD 330: address 56, byte3, bit6 should be enabled.
For MIB2 Discover media: address 5F: byte19, bit4 should be enabled.
Wiring part applies same for both.
-
- Silver Member
- Posts: 493
- Joined: Wed Dec 07, 2016 8:34 pm
- Drives: Polo6r/1.2TSI/DSG7, T-roc'20 1.5TSI/DSG7
- Location: Foothills of Nilgiris, India
Re: Help fitting Reverse Camera with RCD330 - Canbus
Hope this helps.
-
- New
- Posts: 42
- Joined: Sun Apr 26, 2020 10:08 am
- Drives: Polo 6C 1.4TDI 105HP
- Location: Netherlands
Re: Help fitting Reverse Camera with RCD330 - Canbus
I measured the cable with multi meter and the cable is ok, I also do not see other fault codes except the camera.
I plugged an other camera this also doenst work, with an other plug cable (blue).
Do you guys have some ideas??
I plugged an other camera this also doenst work, with an other plug cable (blue).
Do you guys have some ideas??