60/40 suspension kit on 16" on a 6n2??

[alexperkins]

Its hard to say. It could well scrub. RXs are a 7J wheel so are wider than RX2s in the same size, so you may have issues there.

Its recommended to replace the nuts as they are self locking one time use - not particularly expensive, and worthwhile from a safety point of view.

[dub6n2]

The rear shocks on my wife's 6N2 are shot so I've got hold of a 60/40 kit (Jackson tuning setup)

Picking it up this week and will attempt to fit myself too.. Any advice before I go ahead? Haynes manual says I should replace the nuts with new ones? Is that true?

Also I'm looking at sourcing some BBS RX (I) 16' with ET35 offset. I assumed that would be perfectly fine (running on 195/40's) but reading the above comments.. can I expect some issues then???

I would change the bushes as you are on the way. will like to see some pictures when it is fitted mate as I am interested in lowering on that set up

[f6had]

Alex, thanks for that - I didn't realise at all that the RXI was a 7j wheel..

So ET35, the max width should be 6.5j right?

Looks like I need 15' RX2's then..

Regarding the locking nuts, is that a dealer only part?

[benmkiv]

i have a 40mm drop on front and rear on 15" wheels with 50 profile tyres.

this is a nice look on the back, quite close but i have a 12" sub in the boot and can go 5 up np.

[alexperkins]

change to 45s on your next tyre change ben...50s put the speedo out

[benmkiv]

did wonder

do the 6n2 1.0mpi e come with 13" steelys standard i think?

so 45's will put it back right?
it was on the list i just have no money at all atm

[f6had]

It's not really about whether wheels are 15, 16 or even 17' - it's all about wheel width and offset.

I looked into this recently for the Polo and the consensus is that a maximum of 6.5' wheel width coupled with around ET40 offset will be a safe bet and you can go almost as low as you want.

There aren't many or possibly any aftermarket wheels available in such a high offset that are 16' and have a width of 6.5 inches.

What you can do is look at OEM wheels from something like a BMW Mini or Rover/MG ZR that are 16' and probably 6-6.5' wide. Their offsets are probably fine too as they're OEM and designed to stay tucked in.

The only issue you're likely to have is the centre bore which will need to be machined out by a few mm to the 57.1mm required for the Polo hub.

Hope that helps.

[alanjwong]

Has anyone got any photos of a 6n2 on a 60/40 kit on 16's??


Im interested to see what it looks like??


Thanks

[alexperkins]

Are we ever going to fit your new suspension lol

[alanjwong]

We are one day, when I fnally decide. I just wanna see some photos of a polo with the 60/40 kit first.

Im so indesisive, i need to make sure i am getting the right one.

[alanjwong]

The H&R 60/40 kit is ready and waiting to be fitted. Cant wait to get it done. Also the prospect of getting some new 15'' Cades Eros with black centres should make the car look good. Plus a new GTi rear spoiler that needs to be painted and fitted.

[alanjwong]

The H&R 60/40 Sport Cup Kit is now fitted, I will be getting some photos put up as soon as I can take some. Looks really sweet though.

[alanjwong]

Hi,

Im just posting some photos of my car on 16's with the H&R Sport Cup Kit, 60/40. I like the ride comfort and also feels very sporty. I dont think I could go any lower either.

[alanjwong]

What do people resize the images to? because I cant get the image to fit on the screen properly.

[Mart!n-GTI-DK]

DAAAAAAAANG!!! That looks sweeeeeet!!!

Thanks for the word up Alan

I'm definately getting me a "H&R Cup KIT 60/40"

Is it right to asume that the wheels are 7X16" ET35? But what size tires are you running on them?