Page 149 of 331
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Mon May 16, 2016 5:31 am
by RekinPoznan
Ok I have old autoscan before replace BCM but this is no problem right ? tooday when back from work I make new autoscan.
Can you tell me please number of pins to make rewire BCM to max ?
Best regards Chriss
Code: Select all
Chassis Type: 6R (6N0)
Scan: 01 03 08 09 10 15 17 19 25 44 56
VIN: WVWZZZ6RZxxxxxx Mileage: 214410km-133228miles
01-Engine -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: OK 0000
10-Park/Steer Assist -- Status: OK 0000
15-Airbags -- Status: OK 0000
17-Instruments -- Status: Malfunction 0010
19-CAN Gateway -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
56-Radio -- Status: Malfunction 0010
-------------------------------------------------------------------------------
Address 01: Engine (J623-CAYC) Labels: 03L-906-023-CAY.clb
Part No SW: 03L 906 023 G HW: 03L 906 023 D
Component: 1,6l R4 CR td H13 5687
Revision: -------- Serial number:
Coding: 00114016002400080000
Shop #: WSC 12469 483 00190
ASAM Dataset: EV_ECM16TDI02103L906023G 001006
ROD: EV_ECM16TDI02103L906023AH.rod
VCID: 2ABED2A745F0B142BB9A87-807F
No fault code found.
Readiness: 0000 0000
-------------------------------------------------------------------------------
Address 03: ABS Brakes (J104) Labels: 6R0-907-37x-ESP82.clb
Part No SW: 6R0 907 379 AF HW: 6R0 907 379 AF
Component: ESP8.2i front H05 0005
Revision: --------
Coding: 210248E3417100BB842912E882D200421300
Shop #: WSC 02069 000 00000
VCID: 02EE5A079D008502D32A4F-8057
No fault code found.
-------------------------------------------------------------------------------
Address 08: Auto HVAC (J255) Labels: 6R0-907-044.clb
Part No SW: 6R0 907 044 B HW: 6R0 907 044 B
Component: Climatronic H08 0305
Revision: V0000000
VCID: 328ECAC76D20F18203CA7F-8067
No fault code found.
-------------------------------------------------------------------------------
Address 09: Cent. Elect. (J519) Labels: 6R0-937-08x-09.clb
Part No SW: 6R0 937 087 K HW: 6R0 937 087 D
Component: BCM PQ25 H+4 H46 0256
Revision: BF046001 Serial number: 0147 081104191
Coding: 3CB02BBF48E32400933006C07EAB0ED0F08041FF60840040200000000000
Shop #: WSC 65108 001 10485
VCID: 4564811BCCAE763AB688AC-8011
Subsystem 1 - Part No: 1K0 955 559 AH Labels: 1K0-955-559-AG.CLB
Component: RLS 180310 05 54 0403
Coding: 0005F3
Subsystem 2 - Part No SW: 6R0 959 801 R HW: 6R0 959 801 R Labels: 6R0-959-801.CLB
Component: J386__TSG_FT 006 0903
Coding: 18BC30
Subsystem 3 - Part No SW: 6R0 959 802 T HW: 6R0 959 802 T Labels: 6R0-959-802.CLB
Component: J387__TSG_BT 006 0902
Coding: 08BC30
Subsystem 4 - Part No: 1K8 951 171 A
Component: DWA-Sensor 00 001 0103
Coding: 000000
Subsystem 5 - Part No: 1K8 951 605 A
Component: LIN BACKUP HO H11 9004
Coding: 000000
Subsystem 6 - Part No: 1K8 951 171 A
Component: DWA-Sensor 00 001 0103
Coding: 000000
Subsystem 7 - Part No SW: 6R0 959 811 F HW: 6R0 959 811 F
Component: J388__TSG_HL 006 0902
Coding: 08BC32
Subsystem 8 - Part No SW: 6R0 959 812 F HW: 6R0 959 812 F
Component: J389__TSG_HR 006 0902
Coding: 08BC32
No fault code found.
-------------------------------------------------------------------------------
Address 10: Park/Steer Assist (J446) Labels: 6R0-919-475.clb
Part No SW: 6R0 919 475 HW: 6R0 919 475
Component: PARKHILFE 4K H07 0008
Revision: -------- Serial number: 71391006832409
Coding: 100001
Shop #: WSC 124697 483 00190
ASAM Dataset: EV_VW250ParkiAssis2 S01006
ROD: EV_VW250ParkiAssis2.rod
VCID: 7B1027E3FAEAF8CA90EC1A-802F
No fault code found.
-------------------------------------------------------------------------------
Address 15: Airbags (J234) Labels: 5K0-959-655.clb
Part No SW: 6R0 959 655 K HW: 6R0 959 655 K
Component: VW10Airbag00G H08 0020
Revision: -------- Serial number: 003GX000FFGC
Coding: 003047
Shop #: WSC 124697 483 00190
ASAM Dataset: EV_AirbaVW10BPAVW250 A01001
ROD: EV_AirbaVW10BPAVW250_SE25.rod
VCID: 4A7EB227E5B091425BDA67-801F
Crash sensor for side airbag; driver side:
Serial number: 3572SRB40000B418DA05
Crash sensor for side airbag; front passenger side:
Serial number: 3582SRB40000B150DACB
Crash sensor for side airbag; rear; driver side:
Serial number: 3515RRB40696CSQ87GTF
Crash sensor for side airbag; rear; passenger side:
Serial number: 3525RRB405T6DUG6G0B1
No fault code found.
-------------------------------------------------------------------------------
Address 17: Instruments (J285) Labels: 5K0-920-xxx-17.clb
Part No SW: 6R0 920 861 D HW: 6R0 920 861 D
Component: KOMBI H03 0207
Serial number: 00000000000000
Coding: 140E00
Shop #: WSC 124697 483 00190
ASAM Dataset: EV_Kombi_UDS_VDD_RM09 A04052
ROD: EV_Kombi_UDS_VDD_RM09_SK35.rod
VCID: 3686F6D78148E5A22F2203-8063
1 Fault Found:
12583424 - Powertrain Databus
U0002 00 [008] - No Communications
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 229
Mileage: 213614 km
Date: 2016.04.30
Time: 16:50:47
-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533) Labels: 6N0-909-901-6R.clb
Part No SW: 6N0 909 901 HW: 6R0 937 087 D
Component: GW-K-CAN TP20 H46 0256
Revision: BF046001
Coding: 002200
Shop #: WSC 65108 001 10485
VCID: 700A00CFA3AC8392355E85-8025
No fault code found.
-------------------------------------------------------------------------------
Address 25: Immobilizer (J334) Labels: 5K0-920-xxx-25.clb
Part No SW: 5K0 953 234 HW: 5K0 953 234
Component: IMMO H03 0207
Serial number:
Coding: 000000
Shop #: WSC 00000 000 00000
ASAM Dataset: EV_Immo_UDS_VDD_RM09 A03006
ROD: EV_Immo_UDS_VDD_RM09_SE25.rod
VCID: 6A3E12A7857071427B1AC7-803F
No fault code found.
-------------------------------------------------------------------------------
Address 44: Steering Assist Labels: 6Q0-423-156.clb
Part No: 6R0 423 156 B
Component: LenkhilfeTRW V277
Coding: 11230
Shop #: WSC 00788
VCID: 2F88C3B37E12486A6CE45E-807B
No fault code found.
-------------------------------------------------------------------------------
Address 56: Radio (J503) Labels: 1K0-035-1xx-56.lbl
Part No SW: 5M0 035 186 AA HW: 5M0 035 186 AA
Component: Radio RCD310 016 0049
Revision: 01000000 Serial number: VWZ1Z2K7015701
Coding: 0500040002
Shop #: WSC 124697 483 00190
VCID: 6B3017A38A8A604A000CCA-803F
1 Fault Found:
00856 - Radio Antenna
011 - Open Circuit
Freeze Frame:
Fault Status: 01101011
Fault Priority: 5
Fault Frequency: 1
Reset counter: 219
Mileage: 214264 km
Time Indication: 0
Date: 2010.10.03
Time: 18:48:40
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Mon May 16, 2016 7:15 am
by ciclo
You also need to install the wire for reversing light and electrical bridge in J331 relay, and rewiring your fog lights through SB54 fuse as explained in the link - FAQ-
Here you have all info you need:
viewtopic.php?f=10&t=42713&p=477216#p466570 ,
viewtopic.php?f=62&t=67799#p505742
(compare images to select the terminals)
It is the only way to run all lights correctly (
without exception 
) when a BCM Max is installed in 6R non BlueMotion (EU).
For all 6R non Bluemotion (EU). Tested.
DRLs.
Front Parking/Side lights.
Interior lights.
Switches and Instruments lights.
License plate lights. (OEM Leds tech recomended)
Reverse light.
Rear fog light.
Break lights.
Tail lights.
Turn signals.
Cornering lights.
High beam (+ flashes).
Low beam.
Front foglights.
It is not necessary you post another autoscan. (Model Year A, manual gearbox, CAYC, etc...)
Later you can install the leveling system, and the washer system.
Warning (to others): If you have 6R Model Year
'A' with different wires in light switch connector that shown RekinPoznan in above pics and you want to do this, contact me.
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Mon May 16, 2016 11:21 am
by ciclo
benzinkopf wrote:Hi guys. Ciclo, any luck on ur study how they did the rainclosing in polo?
To test for those who like to play with binaries. Rain closing.
Rain Light Sensor
1K0 955 559 AH
Coding: 06302D
or
5K7 955 559 B
Coding: 0714DD
With the same BCM
- With this BCM coding
it not works.
22904ABF48E1240093380E00FE8B16F02EC8614F60862055220000000000
- With this BCM coding
it works.
22904ABF48E1240093380E007ECB16F000C8614F60842055220000000000
If someone is lucky, please post a full scan of BCM. Thanks.
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Mon May 16, 2016 11:59 am
by iichel
So to test
Windows open
Car locked
Pour water on rls?
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Mon May 16, 2016 12:07 pm
by firegrafik
iichel wrote:So to test
Windows open
Car locked
Pour water on rls?
And wait at least 10-15 second after car locking
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Mon May 16, 2016 12:20 pm
by Bachecco
Hi ciclo, i have recieved the resistors for rear led turn light . Where i connect it?
Inviato utilizzando Tapatalk
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Mon May 16, 2016 9:23 pm
by ciclo
Bachecco wrote:Hi ciclo, i have recieved the resistors for rear led turn light . Where i connect it?
LOL!
Taillights connector:
Left
T6/3 White/Black wire
Right
T6/4 Green/Black wire
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Mon May 16, 2016 9:38 pm
by Bachecco
Thank you for the picture. you are always very helpful
Inviato utilizzando Tapatalk
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Tue May 17, 2016 5:45 am
by RekinPoznan
ciclo wrote:You also need to install the wire for reversing light and electrical bridge in J331 relay, and rewiring your fog lights through SB54 fuse as explained in the link - FAQ-
Here you have all info you need:
viewtopic.php?f=10&t=42713&p=477216#p466570 ,
viewtopic.php?f=62&t=67799#p505742
(compare images to select the terminals)
It is the only way to run all lights correctly (
without exception ) when a BCM Max is installed in 6R non BlueMotion (EU).
For all 6R non Bluemotion (EU). Tested.
DRLs.
Front Parking/Side lights.
Interior lights.
Switches and Instruments lights.
License plate lights. (OEM Leds tech recomended)
Reverse light.
Rear fog light.
Break lights.
Tail lights.
Turn signals.
Cornering lights.
High beam (+ flashes).
Low beam.
Front foglights.
It is not necessary you post another autoscan. (Model Year A, manual gearbox, CAYC, etc...)
Later you can install the leveling system, and the washer system.
Warning (to others): If you have 6R Model Year
'A' with different wires in light switch connector that shown RekinPoznan in above pics and you want to do this, contact me.
Thanks for replay
Working now to make rewire the instalation (in progress)
Is neccesary to make new cable to reverse light ? now working fine after BCM replace... mayby after bridge J331 going down this lamp ?
Is possible to use old reverse light cable ? now going from BCM to rear reverse lamp why needed new ?
Best regards and thanks for help Chriss
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Tue May 17, 2016 5:49 am
by ciclo
firegrafik wrote:
And wait at least 10-15 second after car locking
And the wiper stalk? Something to consider?
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Tue May 17, 2016 8:11 am
by ciclo
RekinPoznan wrote:
Thanks for replay
Working now to make rewire the instalation (in progress)
Is neccesary to make new cable to reverse light ? now working fine after BCM replace... mayby after bridge J331 going down this lamp ?
Is possible to use old reverse light cable ? now going from BCM to rear reverse lamp why needed new ?
Best regards and thanks for help Chriss
Hi Chriss, my only intention is to inform.
Reverse light:
Proper installation is as explained in the links, for me it is very useful (and safe) to have the diagnosis of reverse light through the BCM. I know that not matter to other people, but you can be in a terrible situation if other cars on the road don't know that you are in reverse gear and YOU don't know that your reverse light no works.
Remember that during the day you do not know if your reverse light is turning ON.
Similar things happen with the other lights...
The price of a wire are few euros, pounds, etc..., one or more lives are priceless ... I do not want argue about this because only there is one truth. You can see the myriad of terrible accidents that are displayed in the Youtube videos.
Take this opportunity (installation) to increase the security of your car... The car lights are TO SEE and
BE SEEN.
In your coding from 7H0 BCM you have disabled this diagnosis. (it is the reason to work without faults)
Logically you can not use the same wire which is present in your car. This wire in your 6R supplies power to the reverse light and also informs to the BCM about the reverse switch, but it is not for reverse light diagnosis.
If you do not need or do not want to install this new wire, not install it.
The Electric Bridge inserted into J331 relay adapter (relay removed forever) is mandatory for power supply of the low beam through BCM. It is not related with reverse light.
In any case it is my wish that you make a right installation,... I need to know that someone (not be workshop
) is able to do this installation almost without help.
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Tue May 17, 2016 8:30 am
by ciclo
Bachecco wrote:Thank you for the picture. you are always very helpful
Note the heat from resistance for placement.
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Tue May 17, 2016 2:53 pm
by RekinPoznan
ciclo wrote:RekinPoznan wrote:
Thanks for replay
Working now to make rewire the instalation (in progress)
Is neccesary to make new cable to reverse light ? now working fine after BCM replace... mayby after bridge J331 going down this lamp ?
Is possible to use old reverse light cable ? now going from BCM to rear reverse lamp why needed new ?
Best regards and thanks for help Chriss
Hi Chriss, my only intention is to inform.
Reverse light:
Proper installation is as explained in the links, for me it is very useful (and safe) to have the diagnosis of reverse light through the BCM. I know that not matter to other people, but you can be in a terrible situation if other cars on the road don't know that you are in reverse gear and YOU don't know that your reverse light no works.
Remember that during the day you do not know if your reverse light is turning ON.
Similar things happen with the other lights...
The price of a wire are few euros, pounds, etc..., one or more lives are priceless ... I do not want argue about this because only there is one truth. You can see the myriad of terrible accidents that are displayed in the Youtube videos.
Take this opportunity (installation) to increase the security of your car... The car lights are TO SEE and
BE SEEN.
In your coding from 7H0 BCM you have disabled this diagnosis. (it is the reason to work without faults)
Logically you can not use the same wire which is present in your car. This wire in your 6R supplies power to the reverse light and also informs to the BCM about the reverse switch, but it is not for reverse light diagnosis.
If you do not need or do not want to install this new wire, not install it.
The Electric Bridge inserted into J331 relay adapter (relay removed forever) is mandatory for power supply of the low beam through BCM. It is not related with reverse light.
In any case it is my wish that you make a right installation,... I need to know that someone (not be workshop
) is able to do this installation almost without help.
Thanks for replay.
I make this wire for reverse light you have right.
Waiting for the pins, and a few days I will have a revamped installation, cables module-range Xenon I have at the target site, the module also'm just waiting for the pins.
regards Chriss
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Tue May 17, 2016 4:27 pm
by iichel
what do you guys think about retrofitting curtain airbags?
Re: ciclo's Polo. R-line 1.2 TSI 90hp 119gr.
Posted: Tue May 17, 2016 5:01 pm
by vc-10
Hmmm fiddling with airbags is something I'd be really worried about. You'd need new side airbags in the front seats too, as the standard ones have a combined head/thorax airbag that goes up to the roof.
You need to install the Wiring1 and Wiring2 for BCM Max. See and read the entire post and images (BCM Max).