Page 4 of 4
Posted: Thu Nov 27, 2008 1:29 am
by frankiepolo
LeMeph wrote:ah. well then ill just staple my lips back together then lol.
well i can lift my alloys with one finger too! certain degree off bone snapping involved but its possble... lol.
lol, got new wheels coming on friday, but might take a while to refurb and get teh way i want them!
Posted: Thu Nov 27, 2008 9:14 am
by MiWi
Can you upload a movie with the enginesound?
Posted: Thu Nov 27, 2008 10:54 am
by frankiepolo
Posted: Thu Nov 27, 2008 2:15 pm
by NOZ
Very nice fella
hows the rear plate positioning going? My cars rears like yours now but im trying to somehow fit the plate slightly higher then yours is in the pics. in the bit that curves inwards! No hope; plates in the rear window at the mo!
Posted: Thu Nov 27, 2008 2:38 pm
by frankiepolo
NOZ wrote:Very nice fella
hows the rear plate positioning going? My cars rears like yours now but im trying to somehow fit the plate slightly higher then yours is in the pics. in the bit that curves inwards! No hope; plates in the rear window at the mo!
i was thinking of doing this.....
Posted: Thu Nov 27, 2008 2:44 pm
by NOZ
^^ I see. Personally don't like having it there lol. Perhaps if a slight indented recess was made for it?
I was gonna somehow fix it with screws where you had yours BUT on the bottomof the plate so it sits in the gap. No idea lol!!!
Posted: Thu Nov 27, 2008 5:50 pm
by frankiepolo
NOZ wrote:^^ I see. Personally don't like having it there lol. Perhaps if a slight indented recess was made for it?
I was gonna somehow fix it with screws where you had yours BUT on the bottomof the plate so it sits in the gap. No idea lol!!!
yes ill be getting recess mate,
the way ive got my plate just now is at the bottom of bumper with 2 LED screws for the light.
Posted: Fri Nov 28, 2008 1:03 am
by NOZ
Lol I wanted to have 2 LED screws initially but then opted for a light reposition to the middle of the bumper. Shame it wasn't done properly but it works lol (not that the plates actually there!)
Posted: Mon Dec 01, 2008 6:16 pm
by Tim_GTi
Mark5 rear bumper?
Posted: Mon Dec 01, 2008 6:26 pm
by frankiepolo
Tim_GTi wrote:Mark5 rear bumper?
im looking for a mark5 rear bumper, but if i dont get one ill just get a recess made
Re: My 16v polo... Dragon Green, UPDATE PAGE 4
Posted: Tue Feb 24, 2009 10:56 pm
by sc00byd00byd00
frankiepolo wrote:Heres the valver....
BMC CDA Induction kit
Ram air intake
Janspeed full s/s exhaust system
Decat
Supersprint 4-2-1 exhaust manifold
Stage 3 head
Sorg Group N Cams
Ported throttle body
Modified inlet manifold
Dastek Piggyback ECU
Dastek custom mapping
Splitfire platinum spark plugs
Magnecor 8mm Ignition Leads
Removed EGR vavle
Hiya mate. I'm curious about the above mods. what bhp & lp/ft you running at ?
I'm looking to get some more performance out of my 16v and was wondering it would be a more financially viable solution than an engine conversion.
What sort of price range was each of the mods and how difficult were they ?
Re: My 16v polo... Dragon Green, UPDATE PAGE 4
Posted: Tue Feb 24, 2009 11:28 pm
by NFS
Noticed that you are running a raceland manifold like m9. Just wanted to know how did you extend your lambda sensor and did you get any engine management lights pop up? Ive extended m9 using wires from an lambda sensor from a scrappie and used heat shrink crimps to join them but my emissions light cumz up after about 30 minz of driving.