Got Bored Today !

Alex_6n2 · Post by **Alex_6n2** » Wed Feb 14, 2007 7:00 pm

Good lad!

Non of this "Power Drums" crap.

Hammerite?

Ian_R · Post by **Ian_R** » Wed Feb 14, 2007 7:02 pm

Alex_6n2 wrote:Good lad!

Non of this "Power Drums" crap.

Hammerite?

Power Drums ? Nah Mate, Good Old Halfords Spray Paint, Few Coats of Primer, Same with the Black, and Also The Laquer

Gonna throw it on 4 Stands 2 tomorrow and Jet wash the Arches, Also maybe Wind The Coils to The Bottom, As you can see in the Pic there's A Way to go lol

Bepe · Post by **Bepe** » Wed Feb 14, 2007 7:24 pm

this is what mine did look like:

I never got round to taking a pic of the finished thing, only did one side as it took ages sanding it down and getting all the rust off!

Ian_R · Post by **Ian_R** » Wed Feb 14, 2007 7:41 pm

Sod Proper Sanding Down lol, I just attacked mine with the Old Wire Brush lol, You do you'rs Black Yeah ?

Ian_R · Post by **Ian_R** » Wed Feb 14, 2007 7:41 pm

Sod Proper Sanding Down lol, I just attacked mine with the Old Wire Brush lol, You do you'rs Black Yeah ?

Alex_6n2 · Post by **Alex_6n2** » Wed Feb 14, 2007 10:15 pm

Should've used Hammerite mate, better than paint for brakes etc.

Dee-vub · Post by **Dee-vub** » Wed Feb 14, 2007 11:14 pm

Alex_6n2 wrote:Should've used Hammerite mate, better than paint for brakes etc.

He should be ok with the drums due to it not generating that much temp, but with calipers etc, get the hammerite out.

The normal paint still wont last as long though on the drums!

Bepe · Post by **Bepe** » Thu Feb 15, 2007 4:43 pm

did mine silver mate

pip_polo · Post by **pip_polo** » Thu Feb 15, 2007 5:43 pm

i did mine red, i used this stuff from motor world, he said that hammerite wouldn't last as long, cost me 20 squid. looks good though. (mk4 though

)

Alex_6n2 · Post by **Alex_6n2** » Thu Feb 15, 2007 7:21 pm

Oh dear.

Red drums look s**t.

Dee-vub · Post by **Dee-vub** » Fri Feb 16, 2007 9:48 am

You dont want to drag attention to a set of drums. Get them black and hidden!

Arnoldo · Post by **Arnoldo** » Fri Feb 16, 2007 12:42 pm

Goin to get mine calipiers down within the week. What I need to do them? Sand them etc?

Ian_R · Post by **Ian_R** » Fri Feb 16, 2007 12:48 pm

Arnoldo wrote:Goin to get mine calipiers down within the week. What I need to do them? Sand them etc?

Well As Stated, If your Doing the Callipers, Then you'll need hi Temp Paint, ie Hammerite, All i done for the drums, was Wire brush them Down, and A Couple of coats of Primer, Then Black Pain, Then the Laquer, I know at some point i'll have to do them again, but better than looking rusty,

Also Keeping them subtle is the way forward i say! Rather than red etc, No offence to anyother person that has done this, just i dont like things over the top on vag cars, Euro Way always !

Arnoldo · Post by **Arnoldo** » Fri Feb 16, 2007 1:09 pm

I thought u just sprayed the hammerite on just after u wire brushed them?