Rear Bumper.

racerjonzo · Post by **racerjonzo** » Sun Jul 06, 2008 11:34 am

right on the rear bumper tere is 4 rivet/ screw things, i was wondering is there a proper way to get these off? as i had to remove my bottom part for a quick respray( as some nugget with an aygo hit me) and im getting a 16v rear soon so wanted to kno if there is a right way?
i tries hitting one of them but it didnt budge, any help would be good

BTW ive already took the side ones off near the mudflaps etc and just need the 4 rivets removed.

Cheers

JonDo

LeMeph · Post by **LeMeph** » Sun Jul 06, 2008 12:24 pm

if its like the little plastic things im thinking off then what you have to do is push the center tube out. If you clean one up and see a small circle shape in the middle then try pushing it through, but make sure you catch and keep both the tube and the claw shaped thing.

Ive just gotup sdorry if this isnt much cop!

Polo96CL · Post by **Polo96CL** » Sun Jul 06, 2008 11:57 pm

Hey mate, are they the 4 bolt looking things inbetween the crash bar thingy? If so, remove the crash bar to get access and then use a spanner to twist them off. The have the shape cut into the plastic, just keep twisting and they will drop off, even though they look like they aren't.

Hope that helps,

Daz

racerjonzo · Post by **racerjonzo** » Mon Jul 07, 2008 3:03 am

i think its the crash bar bit... its where the boot meets the bumper... just under the wee rubber seal bit for the boot, four spaced out rivet things... just so i kno how to get a 16v bumper off for tomoro... well today now, but yea tried twisting my old one but nothing im afraid... even tried whacking it with a hammer etc. i kno polos are meant to be tough but f*ck sake come how hard is it t remove a bumper

lol

al try the twisting thing first... if nothing then the popping the middle bit
cheers guys, i shall write back up once i have managed to get it off, and shall tell u all the magic way of removing it

, damn i need some sleep lol
cheers agen lads
ciao

JonDo

LeMeph · Post by **LeMeph** » Mon Jul 07, 2008 7:58 pm

get a picture up of these bolts as im still nto sure where you mean.

If you mean directly under the boot lid then its 4 torques screws. If you mean in the wing arch its the plastic poppy things that i went on about earlier.If you mean the funky plastic screw things on the inside then just yank, there s**t anyway.

racerjonzo · Post by **racerjonzo** » Wed Jul 09, 2008 1:09 am

yea got it off lol, was on about the screws under the boot lid, mine are knackered thts why, mine wont budge so was confused how to get them off, but once i was at the 16v it was easier...
sanded it down and primered it... gonna spray it myself see how it turns out... shall get pics up of the steps i went through, see what you guys think... see if its a decent job lol..

JonDo

racerjonzo · Post by **racerjonzo** » Thu Jul 24, 2008 3:22 am

right finally got round to putting pics up... this is how i sprayed my bumper

any extra advice is welcome

now some pics;

sanded it down firstly;

then primered it;

close up;

then two coats of red paint, flash red

;

and yes it does look dull;

then some gloss, think this was two coats

;

another with gloss;

while tht was drying took old bumper off... screws where knackered as previously mentioned but drilled them out, it was the only way thread was fcuked on them

;

then with bumper on car

;

and another;

so what do you guys think? remember it was myself.. no painting qualifications... and in my back garden..

lol so verdicts... it does look much better... and in some lights cant notice the differense in colour but in some its quite noticable

comments

JonDo

vw-po-low · Post by **vw-po-low** » Thu Jul 24, 2008 7:43 am

Not a bad job at all mate.