GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

NFS · Post by **NFS** » Sat Mar 28, 2009 12:51 pm

Ok, finally fitted the GTI inlet manifold and throttle body onto my 1.4 16v polo. Everything is working, the car accelerates etc. However the car is now finding it difficult to idle as the revs jump up n down the 1000 mark. Using my VAG COM i have one fault code that comes up:

- Barometeric / Manifold Pressure Signals: Implausible correlation P1553

I have used the channel 60 to do the adaptation run on the throttle body but no luck. Anyone have a clue what the error means and what can be the possible fault.

Cheers.

Post by **alexperkins** » Sat Mar 28, 2009 4:08 pm

that would be due to the fact its not designed for the engine. from memory its dueo to too much air going in.

ill check elsa when im home and tell you the official word on that error, but theres a chance it cant be fixed as they are somewhat different engines with two different management systems

NFS · Post by **NFS** » Sat Mar 28, 2009 4:48 pm

Is the fault definitely due to too much air entering? If it is, is it possible to cure the problem by mapping the ecu to let it no that it has a bigger throttle body etc?

Post by **alexperkins** » Sat Mar 28, 2009 5:05 pm

im not sure. ill check elsa and let you know

NFS · Post by **NFS** » Sat Mar 28, 2009 6:02 pm

alexperkins wrote:im not sure. ill check elsa and let you know

Do you think you can also check if the GTI and 1.4 16v MAP sensors are the same, as i havent changed that.

Post by **alexperkins** » Sat Mar 28, 2009 6:08 pm

Where does it connect to?

Also, I need the fault code number for that error - what youve given isnt enough for elsa to translate

NFS · Post by **NFS** » Sat Mar 28, 2009 6:12 pm

The one that goes on the side of the intake manifold. I dont no if its MAF or MAP

NFS · Post by **NFS** » Sat Mar 28, 2009 6:17 pm

alexperkins wrote:Where does it connect to?

Also, I need the fault code number for that error - what youve given isnt enough for elsa to translate

Ermm..i believe it was 17961

Post by **alexperkins** » Sat Mar 28, 2009 6:18 pm

right...will have a look

Post by **alexperkins** » Sat Mar 28, 2009 6:23 pm

What engine code is your engine? And what engine code did the manifold come from?

NFS · Post by **NFS** » Sat Mar 28, 2009 6:27 pm

m9 is AUA n dont no what engine code the manifold came off i got the product code which is 036 129 711

Post by **alexperkins** » Sat Mar 28, 2009 6:28 pm

You got the two letters after the 711? If you have MSN pm me lol itll be easier on there! lol

NFS · Post by **NFS** » Sat Mar 28, 2009 6:38 pm

Letters are BJ and ive pm'd u my msn

UK-POLOS.NET - THE VW Polo Forum

GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem

Re: GTI Inlet Manifold & Throttle Fitted - 1 Small Problem